Printed from: PhysLink.com; http://www.physlink.com/News/Index.cfm?ID=123Original publication date: Wednesday November 19, 2003.Supersonic cracks
Historically, the classical physics of continuum has been the basis for most theoretical and computational tools in engineering, and theories relying on numerous phenomenological assumptions have been used. Over the last decades, there has been a new realization that atomic scale behavior is crucial to achieving a more fundamental understanding of how materials fail. There is also the challenge created by the increasing trend to miniaturization in technology as relevant length scales of materials approach the nanoscale. At nanoscales which the continuum description of materials becomes questionable. Scientists use atomic simulations to study how materials behave under extreme conditions. The simulations yield fundamental "ab-initio" information about the mechanisms of deformation and failure at length and time scales unattainable by experimental measurement and unpredictable by continuum theories. With today’s supercomputers, systems up to billions of atoms can be simulated, approaching materials size on the order of micrometers! Such length scales are of immediate interest to engineers. It is estimated that the billion-atom simulations will become routine in a few years, underlining the enormous potential of atomistic methods for technological innovations in materials science. In a recent article in Nature, a team of scientists from Max Planck Institute for Metals Research in Stuttgart and IBM Almaden Research Center in San Jose, California study the dynamics of brittle crack propagation with large-scale atomic simulations. In this article the scientists report the discovery of an important missing feature in the existing theories of dynamic fracture: The elasticity of solids depend on their state of deformation. Metals will weaken, or soften, and polymers may stiffen as the strain approaches the state of materials failure. "It is only for infinitesimal deformation that the elastic moduli can be considered constant and the elasticity of the solid linear," says Prof Dr Huajian Gao, Director at the Max Planck Institute for Metals Research in Stuttgart, Germany. "However, many existing theories model fracture using linear elasticity, and neglect the considerable difference in material behavior at small and large strains. Certainly, this can be considered questionable since materials fail at the tip of a dynamic crack because of the extreme deformation." The scientists hence postulated that hyperelasticity, the elasticity at large strains, can play a governing role in dynamic fracture. In their studies, the scientists show that hyperelasticity, the elasticity at large strains, can dominate the dynamics of fracture. Cracks moving in solids absorb and dissipate energy from the surrounding material. "We discovered a new length scale characterizing the zone near the crack tip from which the crack draws energy to sustain its motion," says Gao. "When materials are under extreme stress, this length scale extends only a few dozens nanometers." This characteristic length scale is found to be proportional to the fracture surface energy and elastic modulus, and inversely proportional to the square of the applied stress. Contrary to the common belief, the crack does not need to transport energy from regions far away from its tip, rather only from a small local region described by the characteristic length scale. If the region around the crack tip becomes stiff due to hyperelasticity, more energy can flow to the crack tip in shorter time. On the other side, energy transport gets slower when there is a local softening zone around the crack tip. Therefore, the scientists conclude that hyperelasticity is crucial for understanding and predicting the dynamics of brittle fracture. When hyperelasticity dominates, cracks can move faster than all elastic waves. This is in clear contrast to the classical theories in which it is believed that the longitudinal elastic wave speed is an impenetrable upper limit of crack speed. Figure shows snapshots of a computer simulation where the crack breaks through the sound barrier and propagates at a supersonic velocity (in glass, for instance with a speed higher than 5.300 m/sec, which is greater than 19,000 km/h). Such phenomenon can only be understood through hyperelasticity. Hyperelasticity dominates fracture energy transport when the size of the hyperelastic zone approaches the energy characteristic length. Under normal experimental conditions, the magnitude of stress may be one or two orders of magnitude smaller than that under atomic simulations. In such cases, the characteristic length is relatively large and the effect of hyperelasticity on effective velocity of energy transport is relatively small. At about one percent of elastic strain, the energy characteristic length is on the order of a few hundred atomic spacing and significant hyperelastic effects are observed. It seems that hyperelasticity can play the governing role especially in nanostructured materials such as thin films, or under high-impact conditions where huge stresses occur, so that the region from which the crack needs to draw energy is small.
The computer simulations reported in the Nature article to prove the concepts of hyperelasticity and energy characteristic length need to attain sufficiently large system sizes, and are hence very resource demanding. These simulations have been performed at the Max Planck Society’s Supercomputer Center in Garching, which is among the most prominent scientific computer centers in the world. |